440C Stainless Steel Sheet 9Cr18Mo 9Cr18Mov D2 For Knife 440c Sheet 1.0*610*2000

440C Stainless Steel Sheet 9Cr18Mo 9Cr18Mov D2 Sheet Used For Knife 440c Flat Bar

AISI 440C steel is characterized by good corrosion resistance in mild domestic and industrial environments, including fresh water, organic materials, mild acids, various petroleum products, coupled with extreme high strength, hardness and wear resistance when in the hardened and tempered condition. Grade 440C stainless steel is capable of attaining, after heat treatment, the highest strength, hardness and wear resistance of all the stainless alloys. Small AISI 440C steel sections can be air cooled and quite large sections oil quenched for maximum through hardness.

Otai Steel is one of professional supplier of 440c stainless steel supplier with reliable quality. The following is our supply range and 440c steel chemical composition and other properties.

1. Supply Range for 440C Stainless Steel

440C steel round bar: diameter 1mm～400mm

440C stainless plate: 0.1-100 thickness x 500-2000mm width x 1000-6000mm length

Other steel shape, like 440c steel sheet, 440C coil, flat bar and customized sizes are available against request

2. Standard of 440C Stainless Steel and Equivalent Steel Grades

3. ASTM A276 440C Steel Chemical Composition and Equivalent’s

4. ASTM 440C Stainless Steel Mechanical Properties

• Physical Properties

5. Forging of 440C Stainless Steel

Preheat to 760oC – 820oC, then heat slowly and uniformly to 1050oC – 1150oC, hold until temperature is uniform throughout the 440c steel section and commence forging immediately. Do not overheat 440c stainless steel as this can cause a loss of toughness and ductility. Do not forge below 900oC. Finished forgings of SS 440c should be cooled slowly in a furnace, warm dry lime or ashes to room temperature and annealed immediately. Air cooling after forging may cause cracking of steel 440c.

6. Machinability of 440C Steel

ASTM Grade 440C stainless steel can be machined well, with all operations such as turning and drilling etc., in the annealed condition. Because of 440C SS high carbon content it machines somewhat like high-speed steel. Because chips are tough and stringy, chip curlers and breakers are important.

As heat treated, the 440 steel series are difficult to machine because of their high hardness. For parts that require extensive machining, the free-machining versions, Type 440F or Type 440F Se, offer improved machining properties.

7. Welding of Stainless Steel 440C

Because of its high-hardness capability, and it can be easily air hardened, the 440c stainless steel is seldom welded. However, if welding is necessary, it should be preheated to 260°C (500°F) and post weld anneal treated at 732-760°C (1350-1400°F) for 6 h followed by slowly cooling in the furnace to prevent cracking. To obtain mechanical properties in the weld similar to those in the base metal, welding consumables of like composition should be considered. Otherwise, AWS E/ER309 might also be considered.

8. Heat Treatment of 440C Stainless Steel

• Hot Working

AISI grade 440C stainless steel is pre-heated at 760°C (1400°F). Temperature can be increased up to 1038-1204°C (1900-2200°F). It should not be heated below 927°C (1700°F). It is then slowly cooled at room temperature and fully annealed.

• Cold Working

ASTM Grade Steel 440C is slightly cold workable using common practices.

• Annealing of 440C Steel

For maximum softness, AISI 440C steel is annealed at 843-871°C (1550-1600°F), followed by slowly cooling in the furnace.

• Tempering of 440C Stainless Steel

Stainless 440C steel can be tempered by soaking at 148°C (300°F). Steel 440c hardness at approximately Rockwell C 60 will be obtained. To remove peak stresses and yet retain maximum hardness, temper at least one hour at 300/350ºF (149/177ºC).

• Hardening of 440C Steel

Stainless steel 440C grade can be hardened by heating at 760°C (1400°F). Temperature can be increased up to 1010°C (1850°F) followed by quenching in warm oil or cool in air. However, don’t overheat, because when overheated, full hardness cannot be obtained.

9. Corrosion Resistance

AISI stainless 440C steel has a corrosion resistance somewhat similar to 410 grade, but lower than 431 grade, also lower than most of the 400 series ferritic stainless steels and all of the 300 series austenitic stainless steels.

10. Applications

ASTM 440C steel has been widely used for parts requiring a combination of excellent wear resistance, plus reasonable corrosion resistance.

ASTM Stainless Steel 440C is used typically in the following applications:

• Cutlery
• Ball bearings and races
• Molds and dies
• High quality knife blades
• Valve components, pump parts,
• Measuring instruments, Surgical instruments
• Wear-resistant textile components.

Otai steel could supply your prime best quality AISI 440C stainless steel for your different application use, no matter big quantity or small. You are welcome to contact us for any requests of 440c steel materials. Please subscribe our newsletters to have the promotion price list for 440c stainless steel frequently.

Jiangsu Mittel Steel Industrial Limited is  located in Wuxi City,  a beautiful city near Shanghai.  Wuxi is close to  Shanghai (BAO STEEL) ,Zhangjiagang (ZPSS),Ningbo (BAO XIN),KUN SHAN (DKSS), enjoy excellent geographic location and convenient water, land and air transportation. , Wuxi become the biggest  stainless steel sheet ,plate and coil  supply Centers in China. Jiangsu Mittel Steel Industrial Limited was established in 1998 years. as one of the largest stockists and manufacturers of industrial grade Stainless Steel products and derivatives in Wuxi ,We keep a stock of 50000 tons every month, so we can delivery goods in fast time.

Our company supplies cold/hot-rolled stainless steel sheets,stainless steel coils and stainless steel Plate to many steel factories from athome and abroad, including Shanxi Taigang Iron& Steel CO, . Ltd (TISCO)Zhangjiagang Pohang (ZPSS), Shanghai BAO STEEL, Ningbo Baoxin and steel factories in Taiwan area, Mainland Chinese and foreign countries and regions. 

Our long-term business lines are 201.202.304(1.4301).304L.316.316L(1.4404).430.409L, 309S ,310S(1.4845).317L.904L.S31803(1.4462).S32750.S32760, Finish: 2B, BA, NO. 1 NO. 4, HL, 8K and so on...Meanwhile, our company is also engaged in the long-term supply of homemade & imported medium and thick plates, galvanized and carbon steel products. 

Adhering to the principle of "quality first and customer foremost",our company will offer long-term service to nationwide manufacturers of household appliances, elevators, tableware, ornaments, tanks and machines. We can offer precise frosted wiredrawing, 8K mirror finishing and skim board oil-abrasion of various specifications at any time. The precisely-processed products will meet your requirements for high quality. Our company is a modern enterprise integrating distribution and storage. 

If you are interested in any of our products or would like to discuss a custom order, please feel free to contact us. We are looking forward to forming successful business relationships with new clients around the world in the near future.